[Mp4-tech] Re: Scalable Video Coding and H.264

[Frank]

Hi Viraj ,
Thanks for the detailed link for the software, I have installed it.
Here is a brief procedure I used to compile the software. I will try to encode the video later...
1) download and extract the software to a folder, suppose you extracted the software to '/tmp'
Before you excute the step two above, you should do the following.  I found this file: '/tmp/JSVM0Software/JSVM0.0/H264Extension/build/linux/lib/H264AVCDecoderLib/make'  is mal-formatted.  I encounter the error during the compiling. (i.e., makefile:40: *** commands commence before first target.  Stop)
I resolved the problem by set each line of the following in that file from original 4 precedingtabs to 3 preceding tabs
   $(OBJ_DIR)/BitReadBuffer.o \
   $(OBJ_DIR)/CabacReader.o \
   $(OBJ_DIR)/CabaDecoder.o \
   $(OBJ_DIR)/ControlMngH264AVCDecoder.o \
   $(OBJ_DIR)/CreaterH264AVCDecoder.o \
   $(OBJ_DIR)/GOPDecoder.o \
   $(OBJ_DIR)/FGSSubbandDecoder.o \
   $(OBJ_DIR)/H264AVCDecoder.o \
   $(OBJ_DIR)/H264AVCDecoderLib.o \
   $(OBJ_DIR)/MbDecoder.o \
   $(OBJ_DIR)/MbParser.o \
   $(OBJ_DIR)/NalUnitParser.o \
   $(OBJ_DIR)/SliceDecoder.o \
   $(OBJ_DIR)/SliceReader.o \
   $(OBJ_DIR)/UvlcReader.o \
2) go to the /tmp/JSVM0Software/JSVM0.0/H264Extension/build/linux
type: 'make' in the commandline
you should see it is been compiling.
The excutable file will be located at '/tmp/JSVM0Software/bin' and the configure files are located at 'JSVM0.0/H264Extension/data/'.    However,  I couldn't find the decode config file. If you can do the encode and decode, please let me know.
hope this helps
Frank
----- Original Message ----- 
From: "viraj ambetkar" <princeofpersia79 gmail.com>
To: "Frank" <fghxu hotmail.com>
Cc: <mp4-tech lists.mpegif.org>
Sent: Tuesday, July 12, 2023 3:47 PM
Subject: Re: Scalable Video Coding and H.264
Hi Frank,
The link for downlaoding the software is specified on the same page as:
http://ip.hhi.de/imagecom_G1/savce/index.htm
Open the page in Internet Explorer or something.  It doesn't load
correctly in Konqueror or Opera on my system.  When the page loads, go
to the section called "Software Download:
Software (JSVM 0 software with sample configuration files)"  below
Fig. 10 on the page.
If you have any issues let me know.  Do you have any documentation on
how to run JSVM and encode sample sequences?  Keep me posted.
Viraj
#############################################################################
On 7/12/05, Frank <fghxu hotmail.com> wrote:
> Hi
> 
> I am looking for the same software.  I could not find the source code at the
> web address you gave. Could you please give me the exact link?    We can try
> to exchange the information in how to compile the software.
> 
> Regards
> 
> Frank
> ----- Original Message ----- 
> From: "viraj ambetkar" <princeofpersia79 gmail.com>
> To: <mp4-tech lists.mpegif.org>
> Sent: Monday, July 11, 2023 3:43 PM
> Subject: [Mp4-tech] Scalable Video Coding and H.264
> 
> 
> > Hello Everyone,
> > 
> > I am trying to get SVC JSVM 0 (the scalable version of H.264) to
> > compile in under Linux.  I have downloaded the source code from:
> > 
> > http://ip.hhi.de/imagecom_G1/savce/index.htm
> > 
> > However, the source code for JSVM 0 never came with documentation on
> > how to compile the code or how to use it to encode test video
> > sequences.  Does anyone have an idea on how to do so?  Is there any
> > documentation available?  I read on some website that JSVM 1 was also
> > released, but I cannot find it anywhere, any clues?
> > 
> > Thanks
> > 
> > _______________________________________________
> > NOTE: Please use clear subject lines for your posts. Include [audio,
> [video], [systems], [general] or another apppropriate identifier to indicate
> the type of question you have.
> > 
> > Note: Conduct on the mailing list is subject to the Antitrust guidelines
> found at
> http://www.mpegif.org/public/documents/vault/mp-out-30042-Antitrust.php
> >